The body frame, underframe structure and panelling was of a light alloy (ICI "Kynal" wrought aluminium), designed as an integral unit in order to achieve lightness combined with strength. The structural underframe, coachwork and flooring members were formed from specially designed Kynal M39/2 extrusions, riveted together with light alloy rivets, and Kynal M39/2 sheets for panelling, Argon arc welded to form continuous sheets from door to door, which was riveted to the frame members. The whole of the inside structure and the underside of the floor was sprayed with blue asbestos to reduce condensation and noise, as well as for insulation. The floor was then covered with two thicknesses of flameproof hardboard and overlaid with linoleum.

BR's conventional bogie of the time was used, which was formed of mild steel, with the main frame members being riveted together and the individual members were partly fabricated. The bolsters were fitted with spring side control and side friction blocks. Roller bearing axleboxes were supplied by British Timken.

Each engine drove an exhauster which was used for the vacuum brakes, which used standard coach brake cylinders.

A dead mans device was built into the throttle, if this handle was released for more than 5 seconds all engines returned to idling, the gearboxes (or clutches on the West Riding sets) returned to neutral (which prevented the engine from stalling) and the brakes were automatically applied.

The 24v electrical system provided 60W lighting in the passenger saloons in standard coach fittings, and the drivers and guards lights were on different circuits. These and the control equipment were powered by alkaline batteries which were charged by dynamos, belt driven by the engines. Underfloor mounted oil burning combustion heaters provided thermostatically controlled warm air through ducting the full length of the vehicles at floor level on both sides. The heater control switches were located in different places depending on the type of vehicle. Driving vehicles had the switches in the cab. TBS's had them in the guards compartment, and on other centre cars above one of the doorways. During warm weather cold air could be supplied to the cars.

West Riding Sets

Two 125 hp Leyland engines were fitted to each car, each powering the inner axle of the nearest bogie. Multiple working provision was made for eight power cars. Start and stop controls were provided for each individual engine. The fuel tanks held 232 gallons.

These vehicles had Lysholm Smith torque converters, which were of a unit construction with the engines. They were made up of: a double acting clutch for connecting the engine to either the pump wheel of the torque convertor drive, or direct to the output shaft; the hydraulic system of the torque convertor; and the freewheels which were incorporated into both the convertor and direct drive to allow the car to over-run the engine. While at one time this set up had been common in road vehicles, by 1953 it had been superseded by the pre-selector system, meaning the DMU's transmission system was obsolete by the time they were built. Derby most likely used this transmission because of it's own previous experience with the 1938 LMS unit.

The clutch was the double-acting type with a neutral position, operated by a single toggle mechanism, which in turn was operated by a double acting air cylinder. The hydraulic portion of the torque convertor consisted of a centrifugal pump in a single casing with a three stage hydraulic turbine which gave a maximum torque multiplication of five to one. The free wheels were of the roller type, built into housings secured to the rear of the convertor housing.

The final drives were of the double reduction type, with an overall reduction of 3.58 to 1, and were developed jointly by Leyland Motors Ltd and Walker Bros. (Wigan) Ltd. These two firms also developed the controls together. All were electo-pnuematically operated from two 24-volt batteries, and consisted of electrical switches which operated magnetic valves throughout the train. The driver had an engine speed control, a clutch control and a direction control. The engine speed was controlled by small air cylinders, with four being built into a unit mounted next to the butterfly valve on the manifold. This provided four engine speeds plus idling.

The clutch had four positions, handle off, neutral, converter drive and direct drive. It was only possible to start the engine or change direction in the neutral position. The clutch was controlled by an air cylinder built into the torque converter, with air being admitted through two magnetic valves adjacent to each converter. To avoid the speed of the train exceeding the engine speed two freewheels were incorporated into the torque converters, one for the converter drive and one for the direct drive. Forward and reverse direction control was obtained by air actuated pistons which operated the forward and reverse sliding pinions. The sets were geared for a normal maximum speed of 62mph.

This first prototype batch could be distinguished by the lack of a centre marker light and by the large front windows, without any dividers.

Engines & Transmission & Controls

All other vehicles had AEC 150hp engines with the standard Wilson epicyclic gearbox. The control system for these differed from the West Riding batch, so they were designated "yellow diamond" (same as the Met Camm Lightweights) as opposed to "red triangle" which the West Riding's were. One vehicle was trialled with automatic gear control system.

West Cumberland Sets

These cars had to be built with modified fittings to reduce the overall width to 8ft 11in, some 3in less than standard. This was because of the very limited clearance on the Maryport & Carlisle line. These cars had a strengthening bar on the inner windscreen, identifyable by the side located wipers.

Interiors

Tubular steel framed seats were trimmed with maroon moquette in the third class and blue uncut in the first. The moquette in both classes was a kind of "flower" pattern, set out in narrow vertical lines. Vynide was used on head rolls and seat borders. First class saloons had a variety of seating arrangements, but second class was mainly one-direction style in a 2+3 arrangement.

Interior panelling was Vynide cloth covered flameproof hardboard, in various colour schemes. Luggage racks were provided along the complete length, formed from light alloy tubes of square section. All windows had pull down blinds. The toilet had primrose plastic panels and rubber floor tiles.